Free comprehensive guide to repairing YLOD on the PS3 console. All videos and techniques provided by gilksy. Using the Gilksy Guide, I successfully fixed the “Yellow Light of Death” (YLOD) on my old 60Gb PS3. All I needed was the following items.
|Published (Last):||22 February 2007|
|PDF File Size:||12.55 Mb|
|ePub File Size:||1.13 Mb|
|Price:||Free* [*Free Regsitration Required]|
Heat sink rubber pads still on ps3 ylod fix gilksy this picture remove before reflowing also hold ribbons out of way while reflowing. If this is the first reflow on the console you are working on, then fluxing is generally not necessary as the solder still should contain enough flux for a good reflow. My memory tells me that dielectric grease performed within a few degrees Celsius of the best performer. Other cleaners may be substituted.
Lift of metal cover plate whilst allowing ribbons to pass through gaps in plate without damage, see below. Using a small flat blade screw driver or slotted torx bit, unscrew cover plate screw. It was much easier than I expected, significantly less complicated and puzzle-like than the PlayStation 2. Vacuum or canned air to clean case and system of dust.
I was able to successfully repair my older, 60 GB PlayStation 3. Place motherboard on a baking dish so that it lies flat, place in the oven for 10 minutes, then remove and let cool for 45 minutes. Now its time to apply new heat sink compound to the 2 processors, when doing this its always best to follow the manufacturers instructions ps3 ylod fix gilksy I believe the process is the same with all types please check instructions that come with pastebefore continuing Ps3 ylod fix gilksy June 19, Lift enclosure out of plastic base, see below.
Remove ribbon cable by carefully lifting black part of connector locking tab. You take a chance using arctic silver because if any squeezes out when you put the heat sink back on and it lands on any components then it can cause them to fry out. Visit the New Ps3 ylod fix gilksy. This will invalidate any warranty.
Page 1 of 2 1 2 Last Jump to page: Also OP, I really recommend that you ps3 ylod fix gilksy some shims around the Cell processor on the die to even out the force because the most common cause of the YLoD can be traced back to ps3 ylod fix gilksy patch of the CBB which is under less pressure than the rest. The guide gipksy using a heat gun, but I used the oven method instead: I once saw a chart comparing gix thermal transfer properties of various brands of CPU thermal compound, and that chart included dielectric grease.
This guide was developed using a 60gb model, remember that other models may be slightly different to disassemble.
YLOD Repair Guide
Preheat oven to degrees. Basically, if you can build your own computer you should be able to handle performing this repair.
Glod sink compound still on in this picture, remove before reflowing. Make sure to reconnect the ribbon cables glod, I accidentally didn’t make a solid connection on two of them which gave me a few headaches.
I ps3 ylod fix gilksy, however, have one system that has been running for six months now. Heat sink rubber ps3 ylod fix gilksy still on in this picture remove before reflowing also hold ribbons out of way while reflowing Congratulations!! When you are ready to start the repair, you should download the Ps3 ylod fix gilksy and print it to use as a guide while you do the repair.
If however your system has needed to be reflowed a second or more times you will probably need to flux the BGA’s in order to acheive positive results from the reflow.
PS3 YLoD Motherboard Repair Guide, With Gilksy Videos
Remove ribbon cable by gklksy lifting black part of connector locking tab. When you are ready to start the repair, you should download the PDF and print it to use as a guide while you do the ps3 ylod fix gilksy 1. Now unclip black rear panel and remove. Using a small flat blade screw driver gjlksy slotted torx bit, unscrew cover plate screw.
The written guide, video and PDF file below will walk you through the entire process and cover all necessary details of the repair. Luckily for you, people have taken it upon themselves to figure out a potential fix, that could bring life back into your black and silver casket. Remove all Ps3 ylod fix gilksy screws marked noting size and position. All I needed was a heat gun, some thermal paste, and rubbing alcohol. The PlayStation 3 would crash or shut itself off long before ever reaching those kinds of temperatures.
I attempted to pop the heat spreader off of the GPU, but it is on their pretty good. All credit for this repair goes to gilksy for his excellent work fi development of this repair technique. Early in December, my PlayStation 3 died. After 15 to 20 seconds move ps3 ylod fix gilksy the next area. Remove small ribbon lift tab and remove control panel. As our consoles are forced to do ps3 ylod fix gilksy and more each generation, we are seeing a decrease in their expected life expectancy.
Then, re-assemble following the guide backwards. Fluxing the BGA’s If this is the first reflow on the console you are working on, then fluxing is generally not necessary as the solder still should contain enough flux for a good reflow. I got it on my watch list.
Repairing a PlayStation 3 with the Yellow Light of Death (YLOD) – Blog
Foez, gilksyy should know by the way that flux does absolutely nothing for you unless you’re reballing the PS3. Originally Posted by DeadlyFoez. YLOD is refered to by Sony as a general hardware failure.
Vacuum cleaner or compressed air blower.